Design of Broadband Matching Network for Complex Reactive Load using L-Matching

Broadband Matching for Complex Recative Load

Authors

  • Jawad Yousaf Department of Electrical and Electronics Engineering, Sungkyunkwan University, Suwon, Republic of Korea
  • Zubair Mehmood Department of Electrical and Electronics Engineering, Sungkyunkwan University, Suwon, Republic of Korea
  • Waseem Abbas Department of Electrical and Electronics Engineering, Sungkyunkwan University, Suwon, Republic of Korea
  • Khuram Shehzad Department of Electrical and Electronics Engineering, Sungkyunkwan University, Suwon, Republic of Korea

Keywords:

L-matching, broadband impedance matching, ideal/non-ideal lumped matching

Abstract

In this work, effect of single and multisection matching with and without ideal lumped components on the impedance matching bandwidth was analyzed. Single and multisection L-matching networks are designed for parallel reactive (RC) load configuration at 10 GHz. The analysis showed that higher section matching with ideal components did not produce significant improvement in fractional bandwidth of matching network for complex parallel RC load. However, more wider impedance bandwidth can be obtained with lower section matching constituting of finite component quality factor (Q) lumped components.

References

Amin, M., J. Yousaf, & S. Iqbal. Single feed circularly polarised omnidirectional bifilar helix antennas with wide axial ratio beamwidth. IET Microwaves, Antennas Propagation 10: 825–830 (2013).

Chen, L-Y V., R. Forse, D. Chase, & R.A. York. Analog tunable matching network using integrated thin-film bst capacitors. In: Proceedings Microwave Symposium Digest, 2004 IEEE MTT-S International, p. 261–264 (2004).

Oraizi, H. & A-R Sharifi. Design and optimization of broadband asymmetrical multisection wilkinson power divider. IEEE Transactions on Microwave Theory and Techniques 54: 2220–2231 (2006).

Pozar, D. Microwave Engineering. John Wiley & Sons, NJ, USA (2009).

Vendelin, G.D., A.M. Pavio, & U.L. Rohde. Microwave Circuit Design using Linear and Nonlinear Techniques. John Wiley & Sons, NJ, USA (2005).

Yang, Y., J. Yi, Y.Y. Woo, & B. Kim. Optimum design for linearity and efficiency of a microwave doherty amplifier using a new load matching technique. Microwave Journal 44: 20-36 (2001).

Yousaf, J., H. Jung, K. Kim, & W. Nah. Design, analysis, and equivalent circuit modeling of dual band pifa using a stub for performance enhancement. Journal of Electromagnetic Engineering and Science 16: 169–181 (2016).

Yousaf, J., M. Amin, S. Iqbal, & H. Durrani. Analysis of conducted emission measurements of dc-dc converter with load for proper filter design. International Journal of Microwave and Optical Technology 10: 464–470 (2015).

Yousaf, J., M. Amin, & S. Iqbal. Circularly polarized wide axial ratio beamwidth omnidirectional bifilar helix antennas. In: Proceedings IEEE First AESS European Conference on Satellite Telecommunications (ESTEL), p.1–6 (2012).

Advanced Design System (ADS). KEYSIGHT Technologies (2017) http://literature.cdn.keysight.com/litweb/pdf/ 5988-3326EN.pdf?id=921864.

Downloads

Published

2021-04-22

How to Cite

Yousaf, J. ., Mehmood, Z. ., Abbas, W. ., & Shehzad, K. . (2021). Design of Broadband Matching Network for Complex Reactive Load using L-Matching: Broadband Matching for Complex Recative Load. Proceedings of the Pakistan Academy of Sciences: A. Physical and Computational Sciences, 54(3), 243–255. Retrieved from http://ppaspk.org/index.php/PPAS-A/article/view/228

Issue

Vol. 54 No. 3 (2017)

Section

Articles